USA: 1-800-4GIBSON
Europe: 00+8004GIBSON1
Customer Service
Gibson RSS Feed
Gibson on YouTube
Gibson on Facebook
Gibson on Twitter
Follow Us
Follow Us
Gibson Support - Tuner Replacement

Slide Easy: Dobro and Resophonic Set Up

by Roger Fritz

Dobro set up for resophonic type instruments is simple and will improve the overall volume and tone. These steps can apply to both fingerstyle and Hawaiian style instruments as well as Biscuit and Spider bridges.

Tools Needed:
  • Small to medium size Phillips head screwdriver and small slotted screwdriver
  • Jeweler's files or nut slot files
  • A flat, hard surface
  • 8" x 11" 100 grit sandpaper
  • A dark felt tip marker.

Here we go:

  1. Tune the instrument to the pitch or tuning that will be used most. Changing tunings dramatically will affect the set up of resophonic instruments so it is best to use only one tuning or closely related tunings. To start, after tuning, play some chords and listen for any discrepancies. Make a note of any and where they come from.
  2. Detune the strings for removal of the tailpiece and cover plate. Remove the screws from the tailpiece and cover plate and keep in safe place. Inspect all parts for visible flaws.
    Slide Easy: Dobro and Resophonic Set Up
  3. With cone or spider level and still in place, gently check for the seating of the unit by placing a finger on top of the bridge saddle and tapping around the outside of the cone with a finger on the other hand.
    Slide Easy: Dobro and Resophonic Set Up

    Some points may rattle while others have a thump. The rattle signifies a point which is not touching the surface correctly. On the biscuit style cones you may rotate them a little at a time while tapping until you hear more thumps than rattles. This indicates the best location for the cone to sit. Using the felt tip pen, make alignment marks on the inside of the "well" and corresponding marks on the cone. This will match up later when reassembling.
    Slide Easy: Dobro and Resophonic Set Up

    For spider style cones, repeat the above process with the fingers tapping on the outer ends of the spider listening for the same response.
    Slide Easy: Dobro and Resophonic Set Up
    If it rattles in several spots, it will need some sanding on the bottom of the legs. Remove the slotted screw that holds the spider to the cone and set in a safe place.
    Slide Easy: Dobro and Resophonic Set Up
    Using the 100 grit sandpaper on the level surface, lay the spider on the surface with the flat side down.
    Slide Easy: Dobro and Resophonic Set Up
    Hold the spider by the bridge and gently rub side to side on the sandpaper. After a few strokes check the bottom of the feet to see where it's touching the paper. Repeat. Set the spider down on the flat hard surface without the sandpaper and check for leg contact. This can be done visible and by tapping the legs. Repeat until the rattles diminish. Reinstall the screw through the spider to the cone. (Note: when the screw has reached the contact point between spider and cone, don't torque it, just 1/4 turn will do.)

  4. On both types, check the surface of the well lip where the cone sits for any unlevel imperfections. Correct with sandpaper or razor blade.
    Slide Easy: Dobro and Resophonic Set Up
  5. Line up cone at marks.
  6. With cover plate off, reinstall tailpiece.
  7. Attach strings and tune.
  8. Make sure the slots on both the bridge and nut are wide enough for the strings to move freely. If not, find a jeweler's file or nut file that's a slight bit wider that the string. Gently enlarge the slot making sure to file downwards toward the tailpiece or the tuners on the nut.
    Slide Easy: Dobro and Resophonic Set Up
    Easy does it. Check as you go for depth and width of slot. You want the string height the same. So also check as you go by laying a screwdriver across the strings. All the strings should touch the bottom of the screwdriver blade.
    Slide Easy: Dobro and Resophonic Set Up
  9. After adjusting, remove the strings and tailpiece.
  10. Line up the cover plate with the screw holes. A trick for reattaching screws: Turn screws in reverse lightly until you hear a tick. Then screw them in. This aligns the threads on both pieces to prevent stripping threads.
    Slide Easy: Dobro and Resophonic Set Up
  11. Reattach tailpiece and strings. Tune to pitch.
  12. Check for any problems. Repeat if needed.

Enjoy and slide on.